Page 2 of 2

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Thu Jun 26, 2008 9:51 pm
by TAPOUT
This is a link to one of the dyno pulls on race gas.

http://www.youtube.com/watch?v=48QRiae0FFE

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Mon Jul 14, 2008 8:35 am
by TAPOUT
http://www.youtube.com/watch?v=ZBTga64Z858

I got two runs Friday night. First pass was pretty clean, but conservative. I just wanted to make sure I made all my shifts. These passes were both on the pump + meth tune. We had to install a new clutch Friday to be able to make this track night happen. I was able to get about 140 miles on the clutch before the passes.
1st pass
60 ft 1.693
330 4.843
1/8th 7.375@95.82
1000 9.542
1/4 11.370@124.34

2nd pass I bogged the launch, but was flat foot shifting and I also stayed in 4th through the traps instead of shifting into 5th like the first run.
60 ft 1.771
330 5.063
1/8th 7.613@96.57
1000 9.774
1/4 11.579@125.54

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Mon Jul 14, 2008 8:58 am
by complacent
Wow! You're launches and 60fts are looking great!

So... Are you itching for 10's now? :twisted:


(might have to get new plates...haha)

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Mon Jul 14, 2008 1:23 pm
by drwrx
TAPOUT wrote: 1st pass
60 ft 1.693
330 4.843
1/8th 7.375@95.82
1000 9.542
1/4 11.370@124.34

2nd pass I bogged the launch, but was flat foot shifting and I also stayed in 4th through the traps instead of shifting into 5th like the first run.
60 ft 1.771
330 5.063
1/8th 7.613@96.57
1000 9.774
1/4 11.579@125.54
Two very consistent runs. The .2 second difference at the 1/8 from the first to the second translated into .2 difference at the finish, even though the speeds on the 2nd run were higher.

What clutch did you install and how did it feel at the track? I'm certain Julian would be interested in knowing.

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Fri Jul 18, 2008 1:02 am
by TAPOUT
We went to an ACT 6 puck with stock flywheel. It felt really good on the first run, but I bogged the second launch. On the first run I just wanted a clean run, on the second I was flat foot shifting, and nailed everything except the launch. I actually dropped to about 3500 RPM in first, then made up some time through the rest of the run. I had more MPH by the 1/8th on the 2nd run. It was also rally hot. The temps on the timeslip show 114*. I can't wait to run on a nice cool night. I think 11.0 or maybe 10.9 is possible on meth, and I am going to shoot for a mid 10 on the C16.

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Tue Jul 22, 2008 10:58 am
by Sabre
VERY impressive 60ft times. I don't think I've seen anyone faster than a 1.6 (but you could be the first!).

Knowing how the 6pucks grab, how's the tranny holding up? Are you dumping or trying to slip it? I just replaced my ClutchMasters Stg 4 6 puck. It's actually the same clutch, only with a kevlar disk now :)

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Sun Jul 27, 2008 6:18 pm
by TAPOUT
First run at the track on the new set up was 11.3@124
http://www.youtube.com/watch?v=ZBTga64Z858

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Mon Jul 28, 2008 3:10 am
by drwrx
Good strong run. I couldn't tell if the Mustang jumped the light or if your reaction time was off.
Very enjoyable watching you leave him in your wake. I also love the commentary.
In any case, NICE RUN!

Was this on race gas with alky injection or just pump.

Re: Does anyone run Alky or meth from their factory I/C sprayer

Posted: Wed Jul 30, 2008 5:58 pm
by TAPOUT
This was pump with meth. I am still trying to slip the clutch a bit. I'm hoping to run 1.5 60 ft's when I put some real tires on the car. I ran these with a 225/50/17 Ventus All Season tire.