Does anyone run Alky or meth from their factory I/C sprayer

2.0, 2.5, NA, FI, it's all good in here

Moderator: Moderators

TAPOUT
Unicycle
Posts: 143
Joined: Tue May 01, 2007 10:52 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by TAPOUT »

This is a link to one of the dyno pulls on race gas.

http://www.youtube.com/watch?v=48QRiae0FFE
I think 600 to the wheels ought to do it...
TAPOUT
Unicycle
Posts: 143
Joined: Tue May 01, 2007 10:52 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by TAPOUT »

http://www.youtube.com/watch?v=ZBTga64Z858

I got two runs Friday night. First pass was pretty clean, but conservative. I just wanted to make sure I made all my shifts. These passes were both on the pump + meth tune. We had to install a new clutch Friday to be able to make this track night happen. I was able to get about 140 miles on the clutch before the passes.
1st pass
60 ft 1.693
330 4.843
1/8th 7.375@95.82
1000 9.542
1/4 11.370@124.34

2nd pass I bogged the launch, but was flat foot shifting and I also stayed in 4th through the traps instead of shifting into 5th like the first run.
60 ft 1.771
330 5.063
1/8th 7.613@96.57
1000 9.774
1/4 11.579@125.54
I think 600 to the wheels ought to do it...
User avatar
complacent
DCAWD Founding Member
Posts: 11651
Joined: Sun Aug 29, 2004 8:00 pm
Location: near the rockies. very.
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by complacent »

Wow! You're launches and 60fts are looking great!

So... Are you itching for 10's now? :twisted:


(might have to get new plates...haha)
colin

a tank, a yammie, a spaceship
i <3 teh 00ntz
User avatar
drwrx
DCAWD Founding Member
Posts: 4382
Joined: Mon Sep 20, 2004 8:00 pm

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by drwrx »

TAPOUT wrote: 1st pass
60 ft 1.693
330 4.843
1/8th 7.375@95.82
1000 9.542
1/4 11.370@124.34

2nd pass I bogged the launch, but was flat foot shifting and I also stayed in 4th through the traps instead of shifting into 5th like the first run.
60 ft 1.771
330 5.063
1/8th 7.613@96.57
1000 9.774
1/4 11.579@125.54
Two very consistent runs. The .2 second difference at the 1/8 from the first to the second translated into .2 difference at the finish, even though the speeds on the 2nd run were higher.

What clutch did you install and how did it feel at the track? I'm certain Julian would be interested in knowing.
TAPOUT
Unicycle
Posts: 143
Joined: Tue May 01, 2007 10:52 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by TAPOUT »

We went to an ACT 6 puck with stock flywheel. It felt really good on the first run, but I bogged the second launch. On the first run I just wanted a clean run, on the second I was flat foot shifting, and nailed everything except the launch. I actually dropped to about 3500 RPM in first, then made up some time through the rest of the run. I had more MPH by the 1/8th on the 2nd run. It was also rally hot. The temps on the timeslip show 114*. I can't wait to run on a nice cool night. I think 11.0 or maybe 10.9 is possible on meth, and I am going to shoot for a mid 10 on the C16.
I think 600 to the wheels ought to do it...
User avatar
Sabre
DCAWD Founding Member
Posts: 21432
Joined: Wed Aug 11, 2004 8:00 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by Sabre »

VERY impressive 60ft times. I don't think I've seen anyone faster than a 1.6 (but you could be the first!).

Knowing how the 6pucks grab, how's the tranny holding up? Are you dumping or trying to slip it? I just replaced my ClutchMasters Stg 4 6 puck. It's actually the same clutch, only with a kevlar disk now :)
Sabre (Julian)
Image
92.5% Stock 04 STI
Good choice putting $4,000 rims on your 1990 Honda Civic. That's like Betty White going out and getting her tits done.
TAPOUT
Unicycle
Posts: 143
Joined: Tue May 01, 2007 10:52 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by TAPOUT »

First run at the track on the new set up was 11.3@124
http://www.youtube.com/watch?v=ZBTga64Z858
I think 600 to the wheels ought to do it...
User avatar
drwrx
DCAWD Founding Member
Posts: 4382
Joined: Mon Sep 20, 2004 8:00 pm

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by drwrx »

Good strong run. I couldn't tell if the Mustang jumped the light or if your reaction time was off.
Very enjoyable watching you leave him in your wake. I also love the commentary.
In any case, NICE RUN!

Was this on race gas with alky injection or just pump.
TAPOUT
Unicycle
Posts: 143
Joined: Tue May 01, 2007 10:52 pm
Location: Springfield, VA
Contact:

Re: Does anyone run Alky or meth from their factory I/C sprayer

Post by TAPOUT »

This was pump with meth. I am still trying to slip the clutch a bit. I'm hoping to run 1.5 60 ft's when I put some real tires on the car. I ran these with a 225/50/17 Ventus All Season tire.
I think 600 to the wheels ought to do it...
Post Reply